Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
Just about every person will have his or her own theory involving Tools You Need to Install a New Bathtub .
Installing a bath tub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate quickly; if you have to open up a wall to eliminate the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to move out the old tub and also set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. As opposed to employing a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you install a new bath tub in your washroom if you have actually currently bought a new tub and don't need to alter the plan of your previous water system pipelines.
Your tools as well as material checklist should consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bathtub until the level checks out degree.
To mount taps, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub must wait up until the tub has been used at least once as this will certainly resolve it right into its last setting.
Getting ready for the Setup
Firstly, the supporting framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets unit to stop pressure on the tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that write-up on Installing A Bathtub through someone on another website. Sharing is good. Helping people is fun. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Book A Free Estimate
Report this page